Page 3 sur 4

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Lun 6 Avr 2020 08:55
de PA0CDY
F5OEO a écrit:Le firmware est en cours de finalisation. Voici le lien du téléchargement (béta) : aller dans la section téléchargement !
Ce forum est ici pour échanger autours de ce firmware.

Hello Evariste,
i use your software and made Eshail qso's with my freinds ,but i want to do dvbs2 on 145Mhz and the pluto stops on 325Mhz .
there is a youtube video how to change the frequency to lower 70Mhz ,my question ,can i do that without distroing your software and what is the best way to do that

good luck with all your projects
73,Peter PA0CDY

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Mar 14 Avr 2020 16:29
de g0mjw
It works for me.

Mike

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Mer 10 Juin 2020 08:29
de 4Z1ZV
I installed the 10/10/2019 firmware from this site.

It works ON for DATV, however it will not work for the narrow band on SDR-Console.

I was told that other versions may work OK.

Any link to such version ?


Thanks

4Z1Zv

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Lun 6 Juil 2020 12:37
de mamado
Hi every one.
thanks for this awesome frimware.
i give it a shot and it's fantastic.

i have one question about latency.
i'm trying OBS,VMIX,Gstreamer "command line" , and all three have latency around "2.8" second. recived with sdrangle and leansdr.

using corei7-7500 as transmitter and receive.

in OBS :
using default setting, get around 6 second latency . But when put "Key frame interval = 1" reduce latency to 2.8 second. this for both reciver sdrangle and leansdr.

in Gstreamer :
this is my command
gst-launch-1.0 v4l2src device="/dev/video2" ! video/x-raw,width=640,height=480 ! videoconvert ! x264enc pass=cbr tune=zerolatency bitrate=1000 sliced-threads=true speed-preset=1 vbv-buf-capacity=20 key-int-max=50 rc-lookahead=1 ! flvmux ! rtmpsink location='rtmp://192.168.2.1:7272/,437,DVBS2,QPSK,1000,34,0,nocalib,1,32, live=1'
also "key-int-max" is the major parameter to reduce Latency from 6 second to 2.8 second.

My question here Can i reduce this 2.8 second to less than one second ?

thank you again ^_^

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Jeu 9 Juil 2020 16:18
de F4VSG
Hello to ALL,

After HamRadio 2019 i bought a Jetson Nano, great to use with my Mini-Lime.
It works great, nice H265 compression output with low latency.
Linux scripting is ‘difficult’ for me I am more an Analog radio-amateur.

After Evariste’s ADALM-Pluto Firmware I am using a PLUTO together with V-mix on a i7 laptop with great fun.
Easy to use for me, but only H264 compression.
After I found on the 06-07 post that there is also a Gstreamer solution with lower latency.

Now my question is there a way to send ffmpeg to the Jetson Nano as output from V-mix,
The Jetson Nano makes H265 and sends it to the Pluto.
Is this possible ??

Or are there more simple ways to have H265 compression ??
Already thanks for feedback.

Fb 73 Robert F4VSG

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Ven 11 Déc 2020 07:29
de F6HJC
Bonjour,
Suite a un mauvais flash de mon pluto, je cherche une solution pour le restaurer. J'ai entendu parler de JTAG ...
Quelqu'un a une info sur ce sujet.
73 de F6HJC

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Ven 11 Déc 2020 21:57
de F6HJC
F6HJC a écrit:Bonjour,
Suite a un mauvais flash de mon pluto, je cherche une solution pour le restaurer. J'ai entendu parler de JTAG ...
Quelqu'un a une info sur ce sujet.
73 de F6HJC

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Sam 12 Déc 2020 08:41
de F1CHF
bjr
je suis étonné de ne pas voir de réponse
ils doivent tous être sur le montage du sapin de noel !
je n'y connais rien mais cet article doit pouvoir t'aider
https://www.hb9afo.ch/articles/pluto/default.htm

good luck

le chf

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Sam 12 Déc 2020 10:13
de F6HJC
Merci Christian


F1CHF a écrit:bjr
je suis étonné de ne pas voir de réponse
ils doivent tous être sur le montage du sapin de noel !
je n'y connais rien mais cet article doit pouvoir t'aider
https://www.hb9afo.ch/articles/pluto/default.htm

good luck

le chf

Re: Firmware DATV/QO100 pour plutosdr

MessagePosté: Mar 29 Juin 2021 14:43
de DreuxPomerleau
Bravo pour ce boulot et merci à vous qui ont répondu. C'est vraiment cool. :)


comment faire un compte onlyfans et commencer à gagner de l'argent voici nos tutos