Double receiver DVB-S/S2 144Mhz-2450Mhz
build it yourself or buy a complete MiniTiounerPro already built for less than 100 euros

Display connection

Messagede G8NOP » Ven 26 Juil 2019 21:39

HI,
I now have a 2.6" Serial:UART/I2C/SPI IPS Super TFT LCD 320x240 display.
As it arrived with no spec sheet I would appreciate a photo of its connections to the MinitiounerPro V2 board. I gather that in one of the photos on the forum the connections are shown incorrectly.
73
Pip G8NOP
G8NOP
 
Messages: 4
Inscription: 24 Mar 2019

Re: Display connection

Messagede sm4ive » Lun 5 Aoû 2019 07:04

Hi on the display you have to make an solder bridge betwen iC2 dots
on Minitiouner pcb there are several sockets you can use i use the one on the side of Tuner. Look at the socket its printed
GND,VCC,SDA,SCL you will se the same on the display
on display VCC, SDA,SCL, GND simple as that GLhttp://www.digole.com/index.php?productID=1271
Dernière édition par sm4ive le Mar 6 Aoû 2019 19:51, édité 1 fois.
sm4ive
 
Messages: 13
Inscription: 14 Mai 2019

Re: Display connection

Messagede G8NOP » Lun 5 Aoû 2019 10:17

Thanks for the advice SM4IVE. I'll progress now and hopefully connect up later today.
73
G8NOP
 
Messages: 4
Inscription: 24 Mar 2019

Re: Display connection

Messagede ik8ozv » Mar 12 Nov 2019 15:48

sm4ive a écrit:Hi on the display you have to make an solder bridge betwen iC2 dots
on Minitiouner pcb there are several sockets you can use i use the one on the side of Tuner. Look at the socket its printed
GND,VCC,SDA,SCL you will se the same on the display
on display VCC, SDA,SCL, GND simple as that GLhttp://www.digole.com/index.php?productID=1271



Please can you tell me the right connection?
I have connected like this:

The VCC of the display to the VCC of the Minitiouner Pro2 Connector JP3
The DATA of the display to the SDA of the Minitiouner Pro2 Connector JP3
The TC/CLK of the display to the SCL of the Minitiouner Pro2 Connector JP3
The GND of the display to the GND of the Minitiouner Pro2 Connector JP3

i have made the bridge from the middle Pad and the Pad named I2C.
When i power up the Minitiouner Pro2 i can see the Display changing colors from
white to orange then to green and finally to blue.
Then it remains black with a light of white and can read on the top:

I2C Address: 0x27 V4.1V+2MB Flash

Please what am i doing wrong?
Thanks
Enzo
MinitunerPro2, NIM: FTS4334; Parabole 100cm Offset, LNB Octagon Green.
PC= I9 / Win10-64bits.
IK8OZV
ik8ozv
 
Messages: 38
Inscription: 04 Aoû 2019

Re: Display connection

Messagede F6DZP » Mer 13 Nov 2019 06:33

Hi Enzo,

All is OK.
Your Digole LCD seems to be OK, it displays all it must show when starting.
It is well connected to JP3

Now you must test it using "TestMyMiniTiouner".

Jean-Pierre F6DZP
F6DZP
 
Messages: 1129
Inscription: 24 Déc 2010

Re: Display connection

Messagede ik8ozv » Mer 13 Nov 2019 10:27

Hello Jean-Pierre,
Thanks for your reply.
Please which is the procedure to test it
And what should I get?
Merci
Enzo
MinitunerPro2, NIM: FTS4334; Parabole 100cm Offset, LNB Octagon Green.
PC= I9 / Win10-64bits.
IK8OZV
ik8ozv
 
Messages: 38
Inscription: 04 Aoû 2019

Re: Display connection

Messagede sm4ive » Mer 13 Nov 2019 15:31

what do you see when you start the software? Minitiouner dispaly only starts when you start the software.
73 Lars SM4IVE
sm4ive
 
Messages: 13
Inscription: 14 Mai 2019

Re: Display connection

Messagede ik8ozv » Mer 13 Nov 2019 15:47

I said before what i see.
When i power up the Minitiouner Pro2 i can see the Display changing colors from
white to orange then to green and finally to blue.
Then it remains black with a light of white and can read on the top:

I2C Address: 0x27 V4.1V+2MB Flash

Thanks
Enzo
MinitunerPro2, NIM: FTS4334; Parabole 100cm Offset, LNB Octagon Green.
PC= I9 / Win10-64bits.
IK8OZV
ik8ozv
 
Messages: 38
Inscription: 04 Aoû 2019

Re: Display connection

Messagede sm4ive » Mer 13 Nov 2019 19:50

ik8ozv a écrit:I said before what i see.
When i power up the Minitiouner Pro2 i can see the Display changing colors from
white to orange then to green and finally to blue.
Then it remains black with a light of white and can read on the top:

I2C Address: 0x27 V4.1V+2MB Flash

Thanks
Enzo


YES but display only works when you start the Minitioune program Connect via usb to computer and start minitioune prgram then display works
sm4ive
 
Messages: 13
Inscription: 14 Mai 2019

Re: Display connection

Messagede F6DZP » Mer 13 Nov 2019 20:08

You can test your disply using the software "TestMyMinTiouner"

Jean-Pierre F6DZP
F6DZP
 
Messages: 1129
Inscription: 24 Déc 2010

Suivante
Forums Statistiques

Qui est en ligne

Utilisateurs parcourant ce forum: Aucun utilisateur enregistré et 7 invités

Options

Retourner vers MiniTiouner Pro

cron