vivadatv.org

Hi hope you can help?

New computer!
11th Gen Intel(R) Core(TM) i7-11700 @ 2.50GHz 2.50 GHz
64-bit operating system
Windows 10 Home 20H2
NVIDIA GeForce RTX 3060 Ti

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
DLL version: 3.2.16
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
USB channels detection
----------------------------------------------------------------------
we have found 2 device(s)
............................................
device 0:
device named: MiniTiouner_Pro_TS2 A
For I2C, we can use this device
OK, we will use it with Handle: 266510992
Serial number for A: DA3RQZ07A
............................................
device 1:
device named: MiniTiouner_Pro_TS2 B
we will not use it
For TS, we can use this device
OK, we will use it with Handle: 266259048
Serial number for B: DA3RQZ07B
............................................
USB driver version: 2.12.34
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
I2C initialisation
----------------------------------------------------------------------
I2C controler INIT success
OK MPSSE is empty
Init MPSSE I2C done!
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
MiniTiouner Pro2 detected
MiniTiounerPro2 detected
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
------ NIM and Demodulator detection ------
STV0910 Identification correct : chip_ident($5), release($1).
writing test OK:255
Serit FTS-433x NIM detected
Monitor Number: 2
initializing STV0903STV/0913/0910
STV0910 init OK
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
------ Synthesizer detection ------
Synthesizer found by reading in a register 117
STV6120 init OK
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
------ LNA booster detection ------
LNA found by reading in register0 the value : 33
2nd LNA found by reading in register0 the value: 33
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
no PPM value in EEprom
**********************************************
AdjustQPSK: 0.00
Adjust8PSK: 0.70
Adjust16APSK: 0.90
Adjust32APSK: 0.90
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
CNRmini_12: 1.70
CNRmini_23: 3.30
CNRmini_34: 4.20
CNRmini_56: 5.10
CNRmini_67: 5.50
CNRmini_78: 5.80
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Recording stopped.
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
External display detection
Digole init OK
Oled init ERROR
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
------TS IP and UDP detection ------
nbr of local IP: 1
IP n° 1 = 192.168.1.76
UDP address : 230.0.0.10 port : 10000 using IP interface : 192.168.1.76
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Interface address used by UDP Client: 192.168.1.76
Config_Messages UDP RX Multicast set OK
************* VLC ****************
Load vlc library succeeded
All functions succeeded to load
VLC Version: 3.0.14 Vetinari
Hardware acceleration is OFF
*********************************

number of programs found: 1
------------------------------
Program1: A71A
Provider : QARS
Service Number: 1
Type of Service : Advanced codec SD Digital Television Service
PMt Pid : 256
Pcr Pid : 259
Video Pid : 257
Video Codec : H264
Audio Pid : 258
Audio Codec : MPA

If I select Graph mode MiniTioune program locks up and have to use CTR ALT DEL to close it.
I have probably mist the odious but I have tried!

73's
Martin

Hello,

I suppose that it is because you use the generic windows graphic driver, so video overlay doesn't work.
You just need to install the specific driver for your graphic card.

Jean-Pierre F6DZP

Hi Jean-Pierre,
Thankyou for a quick response to my call for help.
I have just been on GeForce website and updated my 3060Ti graphics card driver to the latest.
There is no change in how my MiniTioune responds do I have to make any other changes to the settings?
Do I need to change preferred decoder settings if so to what?
Everything seems so complicated struggle to keep up with it all.
All works fine using VLC.
Hope you can help.

73's
Martin

Hi Martin try turning off HW acceleration in VLC and MT, seems VLC doesn't like the RTX cards ? had the same issues with my RTX2060

73 John G7JTT

Hi John,
I assumed as VLC mode was working that it wouldn't affect Graph mode.
Turning of the HW acceleration in VLC and MT, will need help on how to do this.
I will try and catch you on QO100 and talk more.
Most of the time I am confused but with trial and error usually get there.
My system is working well with MiniTiouner in VLC mode also able to run OBS etc. on the one PC at the same tine with plenty of head room.

73's
Martin

Hi,
I have turned off FFMPEG HW acceleration in VLC and HW acceleration in MT as suggested by John G7JTT.
Also have tried the two latest versions of Nvidia drivers.
Non of the above worked.
If I select Graph mode MT locks up.
Are other any other suggestions that I could try.

73's
Martin
G8KOE

Hi All,
Latest information on my PC and MT problem.
Just noticed Dell SupportAssist program had run and installed an update.
Now the Graph mode in MT works.
Just one of those Windows Mistry's.

73's
Martin
G8KOE

Hi,
VLC did an up date and MT stopped working in Graph mode.
I have two monitors connected to my PC and had MT always starting in my second monitor by setting the position in config.
Now changed config so MT starts in my first monitor.
MT now works as it should including enabling HW accelerator in VLC and MT.
If I move MT in Graph mode so display is half on monitor 1 and half on monitor 2 only the half on monitor 1 displayed the video the other half is black.
VLC mode works with half of picture on each monitor.
Hope the information may be of help.

73's
Martin